FT 780 0104
Rev. 2 0610

APPLICATIONS

and hinges are designed for swing doors 8 to 10 mm thick, especially made of glass. They ensure a return to the balanced position (90°).

- In all positions for version ,
- Except outside a
� 10° zone before each stop position (0° and 180°) for version

 
Version "" differs from the
traditional version by the
heavy-duty , 4 mm thick wallplate

 

ASSEMBLING

Door :

  • Height x width : 180 cm x 70 or 190 cm x 95 for version " "
  • Thickness : 8 to 10 mm
  • Maximun load: 31 kg/pair or 45kg/pair for version ""
  • Notch : normal or deep in normal version ; only deep in version ""

Separation from support:

  • With normal notch : 6 mm (normal version)
  • With deep notch: 2 mm (normal version and version "").

Nota : In standard model the wall plate has cut-outs in bottom and top parts, PVC sealing strips (790 02X, 790 06B) or tubular seal (790 08D) can be extended to the hinge’s inside. It is not the case with "45" model. In order to achieve some water tightness it is recommended to use a deeper cut out for the hinge which offers minimum space between glass and wall.

 INSTALLATION

  • Remove the leaves and counterleaves and attach the hinges flat on the doorjamb, making sure they are aligned.
  • Check for the presence of the cork gaskets and install the leaves and counterleaves on the door.
  • slide the clamps onto the cams attached to the doorjamb. Level and staighten the door.
  • Tighten the screws completely (use an Allen wrench). Recommended torque : 0,25 m.kg.
  • In case of an offset, compensation plates are available (thickness 3 mm).
  • Make sure there is no risk of opening the door more than 90° beyond the balanced position. If there is, provide a stop.

FINISH - DECOR

hinges are made of brass and are normally available in three finishes : chrome, matt chrome and gold.

ACCESSORIES

the accessories for use with doors and gates are included in the catalogue, e.g.:

  • Pull knobs, see family 699,
  • stops, see family 799
  • Wipes and door seals, see family 790

PARTS LIST

PART NUMBER


DESCRIPTION


SOLD BY

SALOON� A hinge - chrome-plated brass
Set of 2
SALOON� A hinge - matt chrome-plated brass
Set of 2
SALOON� A hinge - gold brass
Set of 2
SALOON� A 45 hinge - chrome-plated brass
Set of 2
SALOON� A 45 hinge - matt chrome-plated brass
Set of 2
SALOON� A 45 hinge - gold brass
Set of 2
SALOON� SA hinge - chrome-plated brass
Set of 2
SALOON� SA hinge - matt chrome-plated brass
Set of 2
SALOON� SA hinge - gold brass
Set of 2
SALOON� SA 45 hinge - chrome-plated brass
Set of 2
SALOON� SA 45 hinge - matt chrome-plated brass
Set of 2
SALOON� SA 45 - hinge - gold brass
Set of 2
Compensation plate - chrome-plated brass
Unit
Compensation plate - polished brass
Unit
Translucent PVC section for 8 mm glass thickness
Lg 2 ,20 m
Translucent PVC section for 10 mm glass thickness
Lg 2 ,20 m
raising button, to be glued :
- chrome
- matt chrome
- Polished

Unit
"
"
raising button, single, to be screwed :
- chrome
- mat chrome
- Polished
- white

Unit
"
"
"
raising button, double :
- Chrome
- matt chrome
- Polished
- white

Unit
"
"
"
SEE OTHER HINGES FAMILIES
NEW
 
   

 

ADLER SAS - Z.A. La Barogne - 9, Av des 22 Arpents - 77230 Moussy le Neuf - France
Tel.: +33 (0)1.60.03.62.00 - Fax :+33 (0)1.60.03.62.49
E-mail : admin1@adler-sa.com